Brow Factor x Mrs.Highbrow Airbrush Brows Bundle

Description

Bundle Includes:

• 1 x Brow Factor Airbrush Machine Black
• 1 x Brow Factor Brow Shaping Guides – Multipack
• 1 x Mrs.Highbrow Power Stain Airbrush Activator
• 4 x Mrs.Highbrow Power Stain

Directions For Use:

1. Begin by running water through the Airbrush for approximately 15 seconds. Adjust the dial to allow a 2-3 mm opening, which controls the Stain’s airflow.
2. Perform a test spray on a cotton round to check for even dispensing. Test across all pressure modes. We recommend using your machine on the lowest setting.
3. Once you achieve an even spray, the Airbrush is ready for use.
4. Complete a patch test before proceeding with the service.
5. Cleanse the brow area with an oil-free foaming cleanser. Rinse with a damp cotton pad. Ensure brows are dry and free of oils and sebum for optimal Stain Hybrid Dye adhesion.
6. Brush the brows and map as desired.
7. Use mapping thread or paste to shape the brows as desired.
8. Starting from the head of the brow, apply the bottom Brow Border at a slight upward angle towards the arch, following the natural brow shape. Continue applying the border from the arch to the tail at a slight downward angle. Ensure the Brow Borders are aligned neatly and press down firmly with fingers or the back of tweezers. Inadequate application may allow Stain to seep through.
9. Repeat the same process for the top Brow Border, ensuring symmetry and secure placement.
10. Ensure the borders are secure to prevent the Stain Hybrid Dye from seeping beyond the desired area. Visually inspect the ‘Brow Borders‘ on both eyebrows to ensure symmetry.
11. Shake the Stain Hybrid Dye bottle well before use. Fill the dispenser with a 2:1 ratio of Stain with Airbrush Activator.
12. Set the Airbrush Machine to your preferred speed and test spray onto a clean dry cotton pad to check the shade and consistency of the spray.
13. Spray a light layer of Stain from the tail of the eyebrow towards the front of the brows. Let this layer set for 1-2 minutes. You may choose to work on each brow individually or simultaneously.
14. Apply a second layer of Stain, following the same direction – from tail to front. Allow this layer to set for 1-2 minutes before proceeding.
15. For the final layer, work from the tail towards the front, ensuring thorough coverage for the client’s desired look. The number of layers will determine the saturation level for the desired outcome. Typically, 2-3 layers are recommended for most clients. For a more natural appearance, 1-2 layers is recommended.
16. After completing the Stain layering, carefully remove the Brow Borders. If required, use Brow Code Tint Remover or a damp cotton tip to clean the edges of the Airbrush brows.
17. Allow the Stain to remain on the brows for 8 to 12 minutes, depending on the desired intensity and saturation level.
18. Gently remove the Stain with a damp cotton pad, starting from the head of the brow and moving towards the tail. Be careful not to scrub back and forth to avoid removing the Stain Hybrid Dye from the skin.
19. Brush the eyebrows into place to complete the Airbrush Stain application process.

Ingredients:

Mrs.Highbrow Power Stain Airbrush Activator: Aqua, Hydrogen Peroxide, Etidronic Acid, Sodium Salicylate, Citric Acid.

Mrs.Highbrow Power Stain: Amla (Phyllanthus Emblica)Aqueous Extract, Saffron (Crocus Sativus) Flower Aqueous Extract, Aloe vera (Aloe Barbadensis) Leaf Aqueous Extract, Chamomile (Chamomilla Recutita)Aqueous Extract, Rose (Rosa Damascena)Flower Aqueous Extract, Propylene Glycol, Isopropyl Alcohol, P-Phenylenediamine, M-Aminophenol, P-Aminophenol, Phenoxyethanol, 4- Amino-2-Hydroxytoluene, Ethanolamine, Sodium Sulphite, Disodium EDTA, Carbomer, Castor (Ricinus Communis) Seed Oil, Lemon (Citrus Limon) Peel Oil.

Additional Information:

In order to reduce the risk of an allergic reaction, it is important to carry out a skin sensitivity or patch test. This skin sensitivity test must be carried out  48 hours before service for each new client, then every 6 months to ascertain if there is an allergy or sensitivity against the product or if such has emerged since the last application. Please be mindful that no reaction during the test is no guarantee that an allergic reaction will not occur during subsequent treatments.

Testing Procedure:

1. Mix a small amount of the product to be used and apply a small amount to a small area on the inner bend of the elbow.
2. Leave on for 15-20 minutes, then remove with water.
3. If any irritation occurs during this time do not carry out the treatment.